--- Miniterm on /dev/ttyUSB0: 115200,8,N,1 --- --- Quit: Ctrl+] | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H --- U-Boot 2009.08 ( 1月 25 2013 - 15:04:09) CPU: Freescale i.MX50 family 1.1V at 800 MHz mx50 pll1: 800MHz mx50 pll2: 400MHz mx50 pll3: 216MHz ipg clock : 66666666Hz ipg per clock : 66666666Hz uart clock : 24000000Hz ahb clock : 133333333Hz axi_a clock : 400000000Hz axi_b clock : 200000000Hz weim_clock : 100000000Hz ddr clock : 200000000Hz esdhc1 clock : 80000000Hz esdhc2 clock : 80000000Hz esdhc3 clock : 80000000Hz esdhc4 clock : 80000000Hz Board: MX50 RDP board Boot Reason: [POR] Boot Device: SD I2C: ready DRAM: 256 MB MMC: FSL_ESDHC: 0, FSL_ESDHC: 1, FSL_ESDHC: 2 *** Warning - bad CRC or MMC, using default environment In: serial Out: serial Err: serial [_get_sd_number] g_sd_number:0 MMC read: dev # 0, block # 1023, count 1 partition # 0 ... 1 blocks read: OK MMC read: dev # 0, block # 1024, count 1 partition # 0 ... 1 blocks read: OK turning on FL ram p=70000000,size=268435456 MMC read: dev # 0, block # 1023, count 1 partition # 0 ... 1 blocks read: OK MMC read: dev # 0, block # 1024, count 1 partition # 0 ... 1 blocks read: OK [_get_pcba_id-1796] undefined PCBA ID PCB ID is 0 MMC read: dev # 0, block # 18431, count 1 partition # 0 ... 1 blocks read: OK MMC read: dev # 0, block # 18432, count 759 partition # 0 ... 759 blocks read: OK MMC read: dev # 0, block # 19455, count 1 partition # 0 ... 1 blocks read: OK MMC read: dev # 0, block # 19456, count 759 partition # 0 ... 759 blocks read: OK MMC read: dev # 0, block # 14335, count 1 partition # 0 ... 1 blocks read: OK MMC read: dev # 0, block # 14336, count 2228 partition # 0 ... 2228 blocks read: OK Kernel RAM visiable size=254M->254M Detecting HOME+POWER key for recovery ... Hit any key to stop autoboot: 0 MMC read: dev # 0, block # 2048, count 8192 partition # 0 ... 8192 blocks read: OK MMC read: dev # 0, block # 12288, count 768 partition # 0 ... 768 blocks read: OK ## Booting kernel from Legacy Image at 70800000 ... Image Name: Linux-2.6.35.3-hg9facadc85de9-di Created: 2013-01-25 7:01:22 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3346940 Bytes = 3.2 MB Load Address: 70008000 Entry Point: 70008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 70d00000 ... Image Name: ntxinitramfs Created: 2013-02-05 5:38:45 UTC Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 145089 Bytes = 141.7 kB Load Address: 70308000 Entry Point: 70308000 Verifying Checksum ... OK Loading Kernel Image ... OK OK MMC read: dev # 0, block # 1, count 1 partition # 0 ... 1 blocks read: OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Initializing cgroup subsys cpu Linux version 2.6.35.3-hg9facadc85de9-dirty (antony@antony-desktop) (gcc version 4.4.3 (GCC) ) #168 PREEMPT Fri Jan 25 15:01:19 CST 2013 CPU: ARMv7 Processor [412fc085] revision 5 (ARMv7), cr=10c53c7f CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache Machine: Freescale MX50 Reference Design Platform Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64516 Kernel command line: console=ttymxc0 init=/init androidboot.console=ttymxc0 keypad video=mxc_elcdif_fb:off calibration hwcfg_p=0x7ffffe00 hwcfg_sz=512 logo_p=0x7ffa1000 logo_sz=388608 logo_powerlow_p=0x7ff42200 logo_powerlow_sz=388608 waveform_p=0x7fe2ba00 waveform_sz=1140736 mem=254M androidboot.serialno=20030394,b3f7fdff960a45bebbc97f7e0266bf42 PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) allocated 1300480 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Memory: 254MB = 254MB total Memory: 246416k/246416k available, 13680k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xf9e00000 - 0xffe00000 ( 96 MB) vmalloc : 0x90000000 - 0xf4000000 (1600 MB) lowmem : 0x80000000 - 0x8fe00000 ( 254 MB) pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) modules : 0x7f000000 - 0x7fe00000 ( 14 MB) .init : 0x80008000 - 0x80039000 ( 196 kB) .text : 0x80039000 - 0x8089d000 (8592 kB) .data : 0x808be000 - 0x809237c0 ( 406 kB) SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Hierarchical RCU implementation. RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled. NR_IRQS:368 MXC GPIO hardware MXC IRQ initialized MXC_Early serial console at MMIO 0x53fc0000 (options '115200') bootconsole [ttymxc0] enabled Console: colour dummy device 80x30 Calibrating delay loop... 799.53 BogoMIPS (lpj=3997696) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 Initializing cgroup subsys debug Initializing cgroup subsys ns Initializing cgroup subsys cpuacct Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys blkio CPU: Testing write buffer coherency: ok regulator: core version 0.5 NET: Registered protocol family 16 i.MX IRAM pool: 128 KB@0x90040000 hwcfg_size_setup() hwcfg_szie=512 hwcfg_p_setup() hwcfg_p=7ffffe00,vaddr=9006ee00,size=512 NtxHwCfg_GetCfgFldStrVal:[WARNING]Config version too new !! Please update hardware config tool !! hwcfg_p_setup() pcba="(null)" !! CPU is i.MX50 Revision 1.1 [check_hardware_name-329] PCBA ID is 30 mxc_board_init() Set E606E2 key mapping !! Using SDMA I.API MXC DMA API initialized IMX usb wakeup probe IMX usb wakeup probe bio: create slab at 0 regulator: DCDC_3V15: 3150 mV SCSI subsystem initialized CSPI: mxc_spi-2 probed Freescale USB OTG Driver loaded, $Revision: 1.55 $ usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Advanced Linux Sound Architecture Driver Version 1.0.23. Bluetooth: Core ver 2.15 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized mc13892 Rev 0.0 FinVer 0 detected Initializing regulators for mx50 rdp. regulator: SW1: 600 <--> 1375 mV at 600 mV Device spi3.0 probed [msp430_probe-663] MSP430 firmware version C851 Switching to clocksource mxc_timer1 NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Unpacking initramfs... Freeing initrd memory: 140K LPMode driver module loaded Static Power Management for Freescale i.MX5 PM driver module loaded sdram autogating driver module loaded Bus freq driver module loaded ESD DSM mxc_dvfs_core_probe DVFS driver module loaded i.MXC CPU frequency driver DVFS PER driver module loaded ashmem: initialized msgmni has been set to 481 alg: No test for stdrng (krng) cryptodev: driver loaded. io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) By setting, SII driver will not be enabled drivers/video/mxc/mxc_epdc_fb.c(3939):EPD 1024x758 waveform_size_setup() wf_size=1140736 waveform_p_setup() wf_p=7fe2ba00,vaddr=90200a00,size=1140736 logo_size_setup() logo_szie=388608 logo_p_setup() logo_p=7ffa1000,vaddr=90100000,size=388608 logo_powerlow_size_setup() logo_size_powerlow=388608 logo_powerlow_p_setup() logo_p_powerlow=7ff42200,vaddr=90180200,size=388608 [epdc_firmware_func]:fw p=90200a00,size=1140736 [mxc_epdc_fb_fw_handler-3619] drivers/video/mxc/mxc_epdc_fb.c(3654):EPD 1024x758 drivers/video/mxc/mxc_epdc_fb.c ******** mxc_epdc_fb ntx_get_battery_vol: 100 fake_s1d13522_parse_epd_cmdline : epd cmdline parse already done . client0 ,addr=0x68,name=tps65185-1 TPS65185 versions : major=0x1,minor=0x2,version=0x5,RevID=0x65 Serial: MXC Internal UART driver mxcintuart.0: ttymxc0 at MMIO 0x53fc0000 (irq = 32) is a Freescale i.MX console [ttymxc0] enabled, bootconsole disabled console [ttymxc0] enabled, bootconsole disabled mxcintuart.1: ttymxc1 at MMIO 0x53fbc000 (irq = 31) is a Freescale i.MX mxcintuart.2: ttymxc2 at MMIO 0x5000c000 (irq = 33) is a Freescale i.MX loop: module loaded MXC MTD nand Driver 3.0 i.MX GPMI NFC vcan: Virtual CAN interface driver Freescale FlexCAN Driver FEC Ethernet Driver PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: irq 18, io base 0x53f80000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2 fsl-ehci fsl-ehci.1: irq 14, io base 0x53f80200 fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver cdc_acm cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems ARC USBOTG Device Controller driver (1 August 2005) Android usb driver initialize proc/cmdline : androidboot.serialno = 20030394,b3f7fdff960a45bebbc97f7e0266bf42 angela test : proc_cmdline = [20030394] android_usb gadget: android_usb ready otg udc vbus falling wakeup fsl-usb2-udc: bind to driver android_usb android gadget: register function adb android gadget: register function usb_mass_storage android gadget: register function rndis rndis_pdata null in rndis_function_bind_config android_usb gadget: usb_mass_storage, version: 2009/09/11 android_usb gadget: Number of LUNs=2 lun0: LUN: removable file: (no medium) lun1: LUN: removable file: (no medium) mice: PS/2 mouse device common for all mice input: gpio-keys as /devices/platform/gpio-keys/input/input0 MXC keypad loaded input: mxc_power_key as /devices/virtual/input/input1 PMIC powerkey probe [__zForce_ir_touch_init-109] zForce controller with v2 command sets. [zForce_ir_touch_probe-534] Set touch resolution 1024x758 input: zForce-ir-touch as /devices/virtual/input/input2 [zForce_ir_touch_recv_data-183] command BootComplete (0)... pmic rtc probe start using rtc device, mc13892_rtc, for alarms pmic_rtc mc13892_rtc.1: rtc core: registered mc13892_rtc as rtc0 pmic rtc probe succeed i2c /dev entries driver IR NEC protocol handler initialized IR RC5(x) protocol handler initialized IR RC6 protocol handler initialized IR JVC protocol handler initialized IR Sony protocol handler initialized Linux video capture interface: v2.00 usbcore: registered new interface driver uvcvideo USB Video Class driver (v0.1.0) APM Battery Driver MXC WatchDog Driver 2.0 device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com Bluetooth: Virtual HCI driver ver 1.3 Bluetooth: HCI UART driver ver 2.2 Bluetooth: HCIATH3K protocol initialized Bluetooth: Generic Bluetooth USB driver ver 0.6 usbcore: registered new interface driver btusb [drivers/mxc/pmic/mc13892/pmic_battery.c-1024] pmic_battery_probe... power_supply mc13892_charger: charger status: online [zForce_ir_touch_recv_data-208] firmware version 0001 0000 0000 0001 mxsdhci: MXC Secure Digital Host Controller Interface driver mxsdhci: MXC SDHCI Controller Driver. mmc0: SDHCI detect irq 0 irq 1 INTERNAL DMA mxsdhci: MXC SDHCI Controller Driver. mmc1: SDHCI detect irq 273 irq 2 INTERNAL DMA mxsdhci: MXC SDHCI Controller Driver. mmc2: SDHCI detect irq 0 irq 3 INTERNAL DMA usbcore: registered new interface driver usbhid usbhid: USB HID core driver logger: created 64K log 'log_main' logger: created 256K log 'log_events' logger: created 64K log 'log_radio' logger: created 64K log 'log_system' Cirrus Logic CS42888 ALSA SoC Codec Driver No device for DAI imx-ssi-1-0 No device for DAI imx-ssi-1-1 No device for DAI imx-ssi-2-0 No device for DAI imx-ssi-2-1 No device for DAI imx-spdif-dai ALSA device list: No soundcards found. nf_conntrack version 0.5.0 (3852 buckets, 15408 max) IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 can: controller area network core (rev 20090105 abi 8) NET: Registered protocol family 29 can: raw protocol (rev 20090105) can: broadcast manager protocol (rev 20090105 t) Bluetooth: L2CAP ver 2.14 Bluetooth: L2CAP socket layer initialized Bluetooth: SCO (Voice Link) ver 0.6 Bluetooth: SCO socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: HIDP (Human Interface Emulation) ver 1.2 android_usb gadget: high speed config #1: android L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2 read_time: 113/5/19 17:55:31 pmic_rtc mc13892_rtc.1: setting system clock to 2013-06-19 17:55:31 UTC (1371664531) Freeing init memory: 196K mmc0: new high speed SDHC card at address aaaa mmcblk0: mmc0:aaaa SU04G 3.69 GiB mmcblk0: p1 p2 p3 < p5 p6 > p4 [k_wait_update_complete]waitupdate ret=-22,4294937508->4294937508 ========== upd_data.update_region( l, t, w, h ) = ( 0, 0, 1024, 758 )============ TPS65185 temprature data = 0x1d,29 [PROGRESS_BAR-2912] No progess ... init: cannot open '/initlogo.rle' EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) mmc1: new high speed SD card at address 0007 mmcblk1: mmc1:0007 SU02G 1.84 GiB mmcblk1: EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) p1 EXT4-fs (mmcblk0p5): recovery complete EXT4-fs (mmcblk0p5): mounted filesystem with ordered data mode. Opts: nodelalloc EXT4-fs (mmcblk0p6): recovery complete EXT4-fs (mmcblk0p6): mounted filesystem with ordered data mode. Opts: (null) init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' warning: `adbd' uses 32-bit capabilities (legacy support in use) enabling adb bash-3.2# android_usb gadget: high speed config #1: android ========== upd_data.update_region( l, t, w, h ) = ( 0, 0, 758, 1024 )============ ========== upd_data.update_region( l, t, w, h ) = ( 0, 0, 758, 1024 )============ ========== upd_data.update_region( l, t, w, h ) = ( 0, 0, 758, 1024 )============ ========== upd_data.update_region( l, t, w, h ) = ( 0, 0, 758, 1024 )============ ========== upd_data.update_region( l, t, w, h ) = ( 0, 0, 758, 1024 )============ ========== upd_data.update_region( l, t, w, h ) = ( 0, 0, 758, 1024 )============ [drivers/input/touchscreen/zforce_i2c.c-432] zforce_i2c_open() [zForce_ir_touch_recv_data-151] command Activate (0) ... [zForce_ir_touch_recv_data-160] command Resolution (0) ... [zForce_ir_touch_recv_data-194] command Frequency (0) ... [zForce_ir_touch_recv_data-169] command Configuration ... request_suspend_state: on (3->0) at 12773731504 (2013-06-19 17:55:42.250634252 UTC) set front light level : 40 PWMCNT : 0x010c